Sida gidaarka loogu xidho dhagax-dhagax

Talaabada 1: Dulmar ku saabsan Sida gidaarka loogu dhejiyo Dhagax

WAQTIGA:

• Maalinta 1: Prep the site and install the first course (Steps 2–10).
• Maalinta 2: Finish and cap the wall (Steps 11–18).

Tallaabada 2: Cabbir gidaarka

To calculate the number of universal corners to order, measure the height in inches of each outside wall corner, as shown, divide by 16, and round up to the nearest whole number. You’ll fill the area between the corners with flat panels. To calculate how many you’ll need, multiply the wall’s width by its height in feet and divide the resulting area by 2 (each panel covers 2 square feet). Subtract the number of universal corners from the result, then add 10 percent to your order of flat panels. Add one universal corner to be safe.

15 × 60cm Quarzite Rusty Rusty ee Dhagaxa Rakiban si fudud loogu rakibo

Tallaabada 3: Rinjiga hoose si aad u diyaariso darbiga

The panels must be installed above ground level, resting on a plastic support called a starter strip, so you’ll want to paint the wall below the strip to match the stone. Find a spray-paint color similar to the palette of your stone panels and paint the bottom few inches of the wall.

Talaabada 4: Ku rakib Xariiqda Bilowga ah si aad u diyaarisid koorsada koowaad

Set the location for the starter strip, at least 2 inches above any soil. Here, the strip’s lip aligns with the top of a stair on the adjacent side of the corner. Fit your drill/driver with a 3/16-inch masonry bit and drill a pilot hole through a slot in the strip near the corner and into the wall. Drive in a masonry screw to secure that end, then use the 4-foot level to bring the strip to level, and mark a line, as shown. Drill pilot holes and fasten the strip in two or three more spots, maintaining level.

Tallaabada 5: Ka saar tab

Dabaqyada fidsan waxay leeyihiin tabo dhinac kasta ah oo ku dahaadhay meelo bannaan oo ku dheggan laakiin u baahan in laga saaro gees kasta oo gees ka samaysan. Ku naso wejiga guddiga dusha shaqada oo isticmaal daabka 5-in-1 si aad u garaacdo tabka, sida muuqata. Cidhifka fidsan ee ka soo baxay ayaa ka dhigi doona gees cidhiidhi ah.

Tallaabada 6: Calaamadee guddiga

Orod kastaa waxa uu ka bilaabmaa gees, iyada oo dhamaadka dhammaatay ee gees caalami ah oo is dulsaaran dhamaadka gole fidsan (oo tab laga saaray). Marka hore, geeska caalamiga ah ayaa loo qaybiyaa laba qaybood; Cidhifka la dhammeeyey ee gabal kastaa wuxuu bilaabaa koorsada, dabada la gooyayna waxay u galaysaa gole fidsan. Quruxda, jar geeska caalamiga ah si gabal kasta ugu yaraan ugu yaraan 8 inji u ahaado. Ama, sida xaaladdeenna, googoo si ay ugu habboonaato jaranjarada kor u kaca: Ku naso gole fidsan dhinaca ku dheggan ee falinka bilawga ah, ka dibna geesta caalamiga ah kor u rogi, dabada cidhifkeeda dhammaatay ee jaranjarada, oo qor xargo gooyay. , sida ka muuqata.

Tallaabada 7: Iska yaree Dhererka

Ku naso guddi calaamadeysan oo wejiga hoos u saaran oogada shaqada oo ay ku yaalliin looxyo xoq ah oo ka hooseeya labada dhinac ee xariiqda goynta. Isticmaal toosan si aad u calaamadiso gooyn labajibbaaran oo ka baxsan meesha ugu yar ee xariiqda qoraalka ah. Ku dheji miinshaarta wareegta ah oo leh daab dheeman oo kala qaybsan oo jar khadka, adigoo sii maraya shubka iyo sidoo kale fiilada ciddiyaha birta ah. Hubi inaad xidhato muraayadaha badbaadada, maaskarada boodhka, iyo ilaalinta maqalka.

Talaabada 8: Xidh guddida kowaad

Hold the cut universal corner against the wall, bringing its finished end flush with the face of the adjacent flat panel so that the two pieces form a 90° outside corner. Level the universal corner, and drill pilot holes through the nailing strip, as shown, directly through the metal if necessary, in at least two places. Fasten the panel with 1¼-inch self-tapping masonry screws.

Talo: Hayso xoogaa yar oo wareeg ah si aad boodhka uga saarto marka aad dib ugu soo celinayso daloolka duuliyaha, taas oo u oggolaanaysa in masoonuhu uu taabto shubka.

Talaabada 9: dhame orodka

Sii wad rakibidda baallayaasha fidsan ee cabbirkoodu dhan yahay, adigoo ka shaqaynaya hoos koorsada. Markaad u dhawaato dhamaadka, cabbir oo jar qayb qayb ah si aad u buuxiso dhamaadka koorsada. Haddii gabal gooyay uu leeyahay tab labada dhinac ah, isticmaal 5-in-1 qalabka si aad u garaacdo. Geli meesha, dalool duuliyaha, oo ku marooji gidaarka.

Tallaabada 10: Ku rakib Geeska Labaad

Use the cut half of the universal corner from the first course, positioned on the opposite side of the corner to stagger the joints. Slip the tongue on its bottom edge into the groove on top of the flat panel beneath. Position a flat panel, with its tab removed, atop the universal corner in the first course. Be sure it’s cut to a different length than the piece beneath, to offset the joints across the wall. Mark and drill pilot holes for the universal corner, secure it, and install the adjacent flat panel to complete the corner.

Talaabada 11: Isku hagaaji Panelyada ku xiga

Work along the course, brushing out debris from the top groove to ensure that the panels fit together snugly. As you set each new panel, make sure that it’s aligned with the previous panel by nestling a ¼-inch metal rod in the groove along the top edge. The rod should lie flat and bridge the grooves in adjacent panels. If it doesn’t, use the 5-in-1 tool to shim the panel up, or back several screws out of the previous panel and adjust it. When the panels align, drill pilot holes and fasten them to the wall.

Talaabada 12: Dhaqdhaqaaqa Kala-goysyada

If the end of a panel falls in line with a joint on any of the previous courses, you’ll want to cut down its length slightly to maintain staggered joints. Hold the panel in place and mark the nailing strip at a different length. Transfer the mark to the back of the panel, cut it to size, and fasten it to the wall.

Talaabada 13: Jar koorasyada si aad ugu haboonaato koorsada ugu sareysa

On the final course, you’ll need to cut down the height of the panels to fit, removing the nailing strip so that the stone reaches to the top of the wall. Rest a flat panel in place and scribe a cutline on the back at the height of the wall. Set the panel on a work surface, and use the circular saw to cut it to the proper height. You may want to cut your corner pieces to length first, then cut them to the proper height, as shown. Dry-fit the two pieces at the corner to check the fit.

Tallaabada 14: Ku dheji qaybaha

Ka saar geesaha geesaha oo mari kuulyo toosan oo ah xabagta dhismaha ee gadaasha qayb kasta si toos ah, sida lagu muujiyay, si biyuhu ay xor ugu noqdaan inay ku qulqulaan muraayadaha gadaasha oo si fiican u daadiyaan. U deji baalasha gidaarka oo hagaaji si ay ugu habboonaadaan geeska.

Talaabada 15: Deji xidhayaasha

Si aad u sii sugto saqafyada la gooyey, mid walba meel ku hel dhawr dhibcood oo aad ku xidhi karto xidhidhka si aan muuqan ee kala-goysyada dhagaxyada dhexdooda. Ku haynta gabalka, dalool duuliye ka dhex qod guddiga oo gidaarka gal. Ku wadid fur-fure, adigoo madaxa ka hooseeya dusha sare ee guddiga. Ku dabool daboolka daboolka, ka soo ururi boodh miiska goynta, oo ku afuufi weelka qalajinta si aad u sawirto. Waxaad si la mid ah u taaban kartaa daldaloolo kasta. Dhameystir rakibidda muraayadaha koorsada ugu dambeysa.

Talaabada 16: Iska yaree Dhagaxyada

Dooro dhagax-dhagaxa dhawr inji oo ka ballaadhan qoto dheer ee gidaarkaaga xidhan si aad u abuurto laad xad dhaaf ah. Cabbir oo calaamadee dhagaxyada ka-dhagaxa si ay ugu habboonaadaan xagga sare ee darbiga. Isticmaal miinshaarta wareegta ah iyo daab dheeman oo kala qaybsan si aad u jarto dhererka, sida muuqata.

Talaabada 17: Dhagaxa u dhig si aad u daboosho darbiga

La shaqaynta lammaane, kor u qaad dhagaxyada oo ku qallaji dusha sare ee derbiga. Ka saar oo mari xabagta dhismaha dusha sare ee derbiga iyo cidhifyada daaha ka hor inta aanad dib u dejin dhagaxyada; ama, haddii aad doorbidayso muuqaal xitaa ka sii dhab ah, dhig sariir hoobiye adag ah. Hadda dib u tillaabo oo la yaab muuqaalka aan kala go'a lahayn.