Daşdan örtülen diwary nädip örtmeli

1-nji ädim: Diwary daş bilen nädip ýapmalydygyna syn

WAGT:

• 1-nji gün: Prep the site and install the first course (Steps 2–10).
• 2-nji gün: Finish and cap the wall (Steps 11–18).

2-nji ädim: Diwary ölçäň

To calculate the number of universal corners to order, measure the height in inches of each outside wall corner, as shown, divide by 16, and round up to the nearest whole number. You’ll fill the area between the corners with flat panels. To calculate how many you’ll need, multiply the wall’s width by its height in feet and divide the resulting area by 2 (each panel covers 2 square feet). Subtract the number of universal corners from the result, then add 10 percent to your order of flat panels. Add one universal corner to be safe.

Easyeňil gurnamak üçin 15 × 60 sm Rüsti kwarsitli daş

3-nji ädim: Diwary taýýarlamak üçin aşagy boýaglaň

The panels must be installed above ground level, resting on a plastic support called a starter strip, so you’ll want to paint the wall below the strip to match the stone. Find a spray-paint color similar to the palette of your stone panels and paint the bottom few inches of the wall.

4-nji ädim: Birinji kursy taýýarlamak üçin “Starter” zolagyny guruň

Set the location for the starter strip, at least 2 inches above any soil. Here, the strip’s lip aligns with the top of a stair on the adjacent side of the corner. Fit your drill/driver with a 3/16-inch masonry bit and drill a pilot hole through a slot in the strip near the corner and into the wall. Drive in a masonry screw to secure that end, then use the 4-foot level to bring the strip to level, and mark a line, as shown. Drill pilot holes and fasten the strip in two or three more spots, maintaining level.

5-nji ädim: Salgyny aýyryň

Tekiz panelleriň her gapdalynda goňşy tekiz panellerdäki ýerler bar, ýöne burçy emele getirýän islendik ujundan aýyrmaly. Paneliň ýüzüni iş ýüzünde goýuň we görkezilişi ýaly 5-in-1 guralynyň pyçagyny ulanyň. Alnan tekiz gyrasy berk burça öwrüler.

6-njy ädim: Paneli belläň

Her ylgaw, bir burçdan başlaýar, uniwersal burçuň gutarýan ujy tekiz paneliň ujuny örtýär (tab aýrylýar). Birinjiden, ähliumumy burç iki bölege bölünýär; her bölekiň gutarýan gyrasy bir ugra başlaýar we kesilen gyrasy tekiz panele öwrülýär. Estetika üçin, her eseriň azyndan 8 dýuým bolmagy üçin uniwersal burçy kesiň. Ora-da, biziň ýagdaýymyzdaky ýaly, basgançak göterijisine gabat gelmek üçin ony kesiň: Başlangyç zolakda goňşy tarapda tekiz paneli dynç alyň, soňra ähliumumy burçuny tersine aýlaň, gutarýan gyrasyny basgançak ýokarsyna basyň we kesilen çyzgyny ýazyň. görkezilişi ýaly.

7-nji ädim: Uzynlyga çenli kesiň

Bellenen paneli kesilen setiriň iki gapdalynda aşagyndaky tagtalar bilen iş ýüzüne goýuň. Scazylan çyzygyň iň dar nokady boýunça kwadrat görnüşli kesilen belligi bellemek üçin göni ulanyň. Tegelek arra böleklere bölünen göwher pyçak bilen laýyklaşdyryň we betondan, şeýle hem demir dyrnak zolagyndan geçip, çyzyk boýunça kesiň. Howpsuzlyk äýnegi, tozan maskasy we eşidiş goragy hökman dakyň.

8-nji ädim: Birinji paneli berkidiň

Hold the cut universal corner against the wall, bringing its finished end flush with the face of the adjacent flat panel so that the two pieces form a 90° outside corner. Level the universal corner, and drill pilot holes through the nailing strip, as shown, directly through the metal if necessary, in at least two places. Fasten the panel with 1¼-inch self-tapping masonry screws.

Maslahat: Buraw synag synag çukuryndan yza çekilende tozany aýyrmak üçin birneme aýlanmagy dowam etdiriň, örme nurbatynyň betona degmegine ýol açyň.

9-njy ädim: Ylgawy tamamlaň

Doly ölçegli tekiz panelleri gurnamagy dowam etdiriň. Ahyryna ýakynlaşanyňyzda, okuwyň soňuny doldurmak üçin bölekleýin paneli ölçäň we kesiň. Kesilen eseriň iki gapdalynda bir tab bar bolsa, ony ýapmak üçin 5-in-1 guralyny ulanyň. Bölümi ýerinde ýerleşdiriň, pilot deşiklerini burawlaň we diwara nurbatlaň.

10-njy ädim: Ikinji burçy guruň

Use the cut half of the universal corner from the first course, positioned on the opposite side of the corner to stagger the joints. Slip the tongue on its bottom edge into the groove on top of the flat panel beneath. Position a flat panel, with its tab removed, atop the universal corner in the first course. Be sure it’s cut to a different length than the piece beneath, to offset the joints across the wall. Mark and drill pilot holes for the universal corner, secure it, and install the adjacent flat panel to complete the corner.

11-nji ädim: Goňşy panelleri deňleşdiriň

Work along the course, brushing out debris from the top groove to ensure that the panels fit together snugly. As you set each new panel, make sure that it’s aligned with the previous panel by nestling a ¼-inch metal rod in the groove along the top edge. The rod should lie flat and bridge the grooves in adjacent panels. If it doesn’t, use the 5-in-1 tool to shim the panel up, or back several screws out of the previous panel and adjust it. When the panels align, drill pilot holes and fasten them to the wall.

12-nji ädim: Bogunlary sokuň

If the end of a panel falls in line with a joint on any of the previous courses, you’ll want to cut down its length slightly to maintain staggered joints. Hold the panel in place and mark the nailing strip at a different length. Transfer the mark to the back of the panel, cut it to size, and fasten it to the wall.

13-nji ädim: Iň ýokary derse laýyk panelleri kesiň

On the final course, you’ll need to cut down the height of the panels to fit, removing the nailing strip so that the stone reaches to the top of the wall. Rest a flat panel in place and scribe a cutline on the back at the height of the wall. Set the panel on a work surface, and use the circular saw to cut it to the proper height. You may want to cut your corner pieces to length first, then cut them to the proper height, as shown. Dry-fit the two pieces at the corner to check the fit.

14-nji ädim: Bölekleri ýelimläň

Burç panellerini aýyryň we panelleriň aňyrsynda suw akyp, dogry akyp biler ýaly, görkezilişi ýaly her bölekiň arka tarapyna gurluşyk ýeliminiň göni monjuklaryny dikligine sürtüň. Panelleri diwara ýerleşdiriň we burçda gysganç ýerleşdirmek üçin sazlaň.

15-nji ädim: Berkidijileri gark ediň

Kesilen panelleri has ygtybarly üpjün etmek üçin, hersiniň üstünde birnäçe nokat tapyň, bu ýerde daşlaryň arasyndaky bogunlara berkidiji çümdürip bilersiňiz. Bölümi ýerinde saklap, panelden we diwara synag deşigini burawlaň. Paneliň aşagyndaky kelläni çümdürip, nurbat bilen sürüň. Buraw kellelerini örtük bilen örtüň, kesiş stolundan tozan ýygnaň we kamuflaage etmek üçin ony guradyjy gazanyň üstüne atyň. Islendik boşlugy şol bir görnüşde düzedip bilersiňiz. Soňky kursda panelleri gurnamagy tamamlaň.

16-njy ädim: Daş daşlaryny kesiň

Üýtgeşiklik döretmek üçin örtülen diwaryň çuňlugyndan birnäçe dýuým giňlikdäki daş daşyny saýlaň. Diwaryň ýokarsyna laýyk daşlary ölçäň we belläň. Görkezilişi ýaly uzynlygy kesmek üçin tegelek arra we segmentli göwher pyçagyny ulanyň.

17-nji ädim: Daşy diwara ýapmak üçin düzüň

Hyzmatdaş bilen işlemek, daş daşlaryny galdyryň we diwaryň üstünde guradyň. Olary aýyryň we daşlary täzeden goýmazdan ozal diwaryň ýokarsyna we şkafyň gyralaryna gurluşyk ýelimini çalyň; ýa-da has ygtybarly görnüşi isleseňiz, olary gaty krowatda goýuň. Indi bir ädim yza çekiň we üznüksiz görnüşe haýran galyň.