Tosh bilan qoplangan devorni qanday qoplash kerak

1-qadam: Devorni tosh bilan qanday qoplash haqida umumiy ko'rinish

Xronologiya:

• 1-kun: Prep the site and install the first course (Steps 2–10).
• 2-kun: Finish and cap the wall (Steps 11–18).

2-qadam: Devorni o'lchash

To calculate the number of universal corners to order, measure the height in inches of each outside wall corner, as shown, divide by 16, and round up to the nearest whole number. You’ll fill the area between the corners with flat panels. To calculate how many you’ll need, multiply the wall’s width by its height in feet and divide the resulting area by 2 (each panel covers 2 square feet). Subtract the number of universal corners from the result, then add 10 percent to your order of flat panels. Add one universal corner to be safe.

Oson o'rnatish uchun 15 × 60 sm Rusty Quarzite Stacked Stone

3-qadam: Devorni tayyorlash uchun pastki qismini bo'yash

The panels must be installed above ground level, resting on a plastic support called a starter strip, so you’ll want to paint the wall below the strip to match the stone. Find a spray-paint color similar to the palette of your stone panels and paint the bottom few inches of the wall.

4-qadam: Birinchi kursni tayyorlash uchun boshlang'ich tasmasini o'rnating

Set the location for the starter strip, at least 2 inches above any soil. Here, the strip’s lip aligns with the top of a stair on the adjacent side of the corner. Fit your drill/driver with a 3/16-inch masonry bit and drill a pilot hole through a slot in the strip near the corner and into the wall. Drive in a masonry screw to secure that end, then use the 4-foot level to bring the strip to level, and mark a line, as shown. Drill pilot holes and fasten the strip in two or three more spots, maintaining level.

5-qadam: Tabni olib tashlang

Yassi panellarning har bir tomonida qo'shni tekis panellardagi tirqishlar bilan bog'langan yorliq mavjud, ammo burchakni tashkil etuvchi har qanday uchidan olib tashlanishi kerak. Panelni ish yuzasiga yuqoriga qaratib qo'ying va ko'rsatilganidek, yorliqni yiqitish uchun 5-in-1 asbobning pichog'idan foydalaning. Olingan tekis chekka qattiq burchak hosil qiladi.

6-qadam: Panelni belgilang

Har bir yugurish burchakdan boshlanadi, universal burchakning tugallangan uchi tekis panelning uchi bilan bir-biriga yopishadi (yorliq olib tashlangan). Birinchidan, universal burchak ikki qismga bo'linadi; har bir bo'lakning tayyor chekkasi kursni boshlaydi va kesilgan qirrasi tekis panelga tushadi. Estetika uchun universal burchakni kesib oling, shunda har bir qism kamida 8 santimetr uzunlikda bo'ladi. Yoki, bizning holatimizda bo'lgani kabi, uni zinapoya ko'taruvchisiga to'g'ri kelishi uchun kesib oling: boshlang'ich chizig'ining qo'shni tomoniga tekis panelni qo'ying, so'ngra universal burchakni teskari aylantiring, uning tugallangan chetini zinapoya ko'targichiga qo'ying va kesilgan chiziqni chizib oling. , ko'rsatilganidek.

7-qadam: Uzunlikka kesib oling

Belgilangan panelni ish yuzasiga pastga qaratib qo'ying, uning ostida kesilgan chiziqning har ikki tomonida hurda taxtalari bor. Chizilgan chiziqning eng tor nuqtasi bo'ylab kvadrat shaklida kesilgan chiziqni belgilash uchun to'g'ri chiziqdan foydalaning. Dumaloq arrani segmentli olmosli pichoq bilan o'rnating va chiziq bo'ylab beton va metall tirnoq chizig'idan o'tib kesib oling. Xavfsizlik ko'zoynagi, changdan himoyalangan niqob va eshitish vositasini taqishingizga ishonch hosil qiling.

8-qadam: Birinchi panelni mahkamlang

Hold the cut universal corner against the wall, bringing its finished end flush with the face of the adjacent flat panel so that the two pieces form a 90° outside corner. Level the universal corner, and drill pilot holes through the nailing strip, as shown, directly through the metal if necessary, in at least two places. Fasten the panel with 1¼-inch self-tapping masonry screws.

Maslahat: Matkapni uchuvchi teshikdan tashqariga chiqarayotganda changni tozalash uchun burg'ulash vintining betonga tegib ketishiga imkon berish uchun tishingizni aylantiring.

9-qadam: Yugurishni tugating

To'liq o'lchamli yassi panellarni o'rnatishni davom eting, yo'l bo'ylab harakatlaning. Oxiriga yaqinlashganingizda, kursning oxirini to'ldirish uchun qisman panelni o'lchang va kesib oling. Agar kesilgan qismning har ikki tomonida yorliq bo'lsa, uni yiqitish uchun 5-in-1 vositasidan foydalaning. Buyumni joyiga qo'ying, uchuvchi teshiklarni burg'ulang va devorga burang.

10-qadam: Ikkinchi burchakni o'rnating

Use the cut half of the universal corner from the first course, positioned on the opposite side of the corner to stagger the joints. Slip the tongue on its bottom edge into the groove on top of the flat panel beneath. Position a flat panel, with its tab removed, atop the universal corner in the first course. Be sure it’s cut to a different length than the piece beneath, to offset the joints across the wall. Mark and drill pilot holes for the universal corner, secure it, and install the adjacent flat panel to complete the corner.

11-qadam: Qo'shni panellarni tekislang

Work along the course, brushing out debris from the top groove to ensure that the panels fit together snugly. As you set each new panel, make sure that it’s aligned with the previous panel by nestling a ¼-inch metal rod in the groove along the top edge. The rod should lie flat and bridge the grooves in adjacent panels. If it doesn’t, use the 5-in-1 tool to shim the panel up, or back several screws out of the previous panel and adjust it. When the panels align, drill pilot holes and fasten them to the wall.

12-qadam: bo'g'inlarni silkit

If the end of a panel falls in line with a joint on any of the previous courses, you’ll want to cut down its length slightly to maintain staggered joints. Hold the panel in place and mark the nailing strip at a different length. Transfer the mark to the back of the panel, cut it to size, and fasten it to the wall.

13-qadam: Yuqori kursga mos keladigan panellarni kesib oling

On the final course, you’ll need to cut down the height of the panels to fit, removing the nailing strip so that the stone reaches to the top of the wall. Rest a flat panel in place and scribe a cutline on the back at the height of the wall. Set the panel on a work surface, and use the circular saw to cut it to the proper height. You may want to cut your corner pieces to length first, then cut them to the proper height, as shown. Dry-fit the two pieces at the corner to check the fit.

14-qadam: Bo'laklarni yopishtiring

Burchak panellarini olib tashlang va har bir bo'lakning orqa tomoniga ko'rsatilgandek vertikal yo'nalishlarda qurilish yopishtiruvchi tekis boncuklarni qo'llang, shunda panellar orqasida suv erkin oqishi va to'g'ri oqishi uchun. Panellarni devorga o'rnating va ularni burchakka mahkam o'rnashtirish uchun sozlang.

15-qadam: mahkamlagichlarni cho'zing

Kesilgan panellarni yanada mahkamlash uchun har birida bir nechta joylarni toping, u erda siz mahkamlagichni toshlar orasidagi bo'g'inlarga sezilmaydigan qilib qo'yishingiz mumkin. Parchani joyida ushlab, panel orqali va devorga uchuvchi teshik oching. Panelning yuzasiga boshni cho'ktirib, g'isht vintiga o'tkazing. Vintlardek boshlarini shlyapa bilan yoping, kesish stolidan bir oz chang to'plang va uni kamuflyaj qilish uchun quritish plitasiga puflang. Xuddi shu tarzda siz har qanday bo'shliqlarni tegizishingiz mumkin. Yakuniy kursda panellarni o'rnatishni tugating.

16-qadam: Qopqoqlarni kesib oling

Qopqoqni yaratish uchun devoringizning chuqurligidan bir necha dyuym kengroq toshni tanlang. Devorning yuqori qismiga mos keladigan toshlarni o'lchab, belgilang. Ko'rsatilganidek, uzunlikni kesish uchun dumaloq arra va segmentli olmosli pichoqdan foydalaning.

17-qadam: Toshni devorga yopish uchun o'rnating

Sherik bilan ishlash, toshlarni ko'taring va ularni devorning tepasiga quritib qo'ying. Toshlarni qayta tiklashdan oldin ularni olib tashlang va devorning yuqori qismiga va qoplamaning chetlariga qurilish yopishtiruvchi qo'llang; yoki, agar siz yanada haqiqiy ko'rinishni afzal ko'rsangiz, ularni qattiq ohak to'shagiga qo'ying. Endi bir qadam orqaga qayting va beg'ubor ko'rinishga hayron bo'ling.