Kumaha Clad Tembok dina Batu-batu clad

Lengkah 1: Ihtisar pikeun Kumaha Ngahias Tembok dina Batu

WAKTU:

• Dinten 1: Prep the site and install the first course (Steps 2–10).
• Dinten 2: Finish and cap the wall (Steps 11–18).

Lengkah 2: Ukur Tembok

To calculate the number of universal corners to order, measure the height in inches of each outside wall corner, as shown, divide by 16, and round up to the nearest whole number. You’ll fill the area between the corners with flat panels. To calculate how many you’ll need, multiply the wall’s width by its height in feet and divide the resulting area by 2 (each panel covers 2 square feet). Subtract the number of universal corners from the result, then add 10 percent to your order of flat panels. Add one universal corner to be safe.

15 × 60cm Rusty Quarzite tumpuk Batu pikeun Instalasi Gampang

Lengkah 3: Cét Bawah pikeun Nyiapkeun Tembok

The panels must be installed above ground level, resting on a plastic support called a starter strip, so you’ll want to paint the wall below the strip to match the stone. Find a spray-paint color similar to the palette of your stone panels and paint the bottom few inches of the wall.

Lengkah 4: Pasang Jalur Starter pikeun Nyiapkeun Kursus Kahiji

Set the location for the starter strip, at least 2 inches above any soil. Here, the strip’s lip aligns with the top of a stair on the adjacent side of the corner. Fit your drill/driver with a 3/16-inch masonry bit and drill a pilot hole through a slot in the strip near the corner and into the wall. Drive in a masonry screw to secure that end, then use the 4-foot level to bring the strip to level, and mark a line, as shown. Drill pilot holes and fasten the strip in two or three more spots, maintaining level.

Lengkah 5: Cabut Tab

Panel datar gaduh tab dina saban gigir anu meshes sareng slot dina panel datar anu padeukeut tapi kedah dipiceun tina tungtung anu ngabentuk sudut. Istirahat panel faceup dina permukaan gawé sarta ngagunakeun sabeulah alat 5-in-1 pikeun sambel tab kaluar, sakumaha ditémbongkeun. Ujung datar anu dihasilkeun bakal nyieun sudut kedap.

Lengkah 6: Cirian Panel

Unggal ngajalankeun dimimitian dina sudut, kalawan tungtung rengse sudut universal tumpang tindih tungtung panel datar (kalawan tab dihapus). Kahiji, sudut universal dipotong jadi dua lembar; ujung rengse unggal sapotong dimimitian tangtu, sarta ujung cut butts kana panel datar. Pikeun éstétika, potong sudut universal supados unggal potongan panjangna sahenteuna 8 inci. Atawa, sakumaha dina kasus urang, motong éta pikeun nyocogkeun kana riser stair: Istirahat panel datar di sisi padeukeut dina strip starter, teras puterkeun sudut universal tibalik ka handap, butt ujung na rengse ngalawan riser stair, sarta juru tulis cutline a , sakumaha ditémbongkeun.

Lengkah 7: Potong Panjang

Istirahat panel ditandaan facedown dina permukaan gawé kalawan papan besi tua handapeun eta dina dua sisi cutline nu. Paké straightedge pikeun nandaan cutline kuadrat-off sapanjang titik narrowest tina garis scribed. Nyocogkeun ragaji sirkular ku sabeulah inten segmented sarta motong sapanjang garis, ngaliwatan beton ogé strip nailing logam. Pastikeun ngagem kacamata kaamanan, masker lebu, sareng panyalindungan dédéngéan.

Lengkah 8: Nyepetkeun Panel Kahiji

Hold the cut universal corner against the wall, bringing its finished end flush with the face of the adjacent flat panel so that the two pieces form a 90° outside corner. Level the universal corner, and drill pilot holes through the nailing strip, as shown, directly through the metal if necessary, in at least two places. Fasten the panel with 1¼-inch self-tapping masonry screws.

Tip: Tetep bit Anjeun spinning pikeun miceun lebu anjeun deui bor kaluar tina liang pilot, sahingga screw masonry ngetok kana beton.

Lengkah 9: Rengse Run

Teruskeun masang panél datar ukuran pinuh, jalan-jalan ka handap. Nalika anjeun caket tungtung, ukur sareng potong panel parsial pikeun ngeusian tungtung kursus. Upami potongan potongan ngagaduhan tab dina dua sisi, paké alat 5-in-1 pikeun ngetokna. Nyocogkeun sapotong dina tempatna, bor liang pilot, sarta screw ka témbok.

Lengkah 10: Pasang Sudut Kadua

Use the cut half of the universal corner from the first course, positioned on the opposite side of the corner to stagger the joints. Slip the tongue on its bottom edge into the groove on top of the flat panel beneath. Position a flat panel, with its tab removed, atop the universal corner in the first course. Be sure it’s cut to a different length than the piece beneath, to offset the joints across the wall. Mark and drill pilot holes for the universal corner, secure it, and install the adjacent flat panel to complete the corner.

Lengkah 11: Align Panels Padeukeut

Work along the course, brushing out debris from the top groove to ensure that the panels fit together snugly. As you set each new panel, make sure that it’s aligned with the previous panel by nestling a ¼-inch metal rod in the groove along the top edge. The rod should lie flat and bridge the grooves in adjacent panels. If it doesn’t, use the 5-in-1 tool to shim the panel up, or back several screws out of the previous panel and adjust it. When the panels align, drill pilot holes and fasten them to the wall.

Lengkah 12: Stagger sendi

If the end of a panel falls in line with a joint on any of the previous courses, you’ll want to cut down its length slightly to maintain staggered joints. Hold the panel in place and mark the nailing strip at a different length. Transfer the mark to the back of the panel, cut it to size, and fasten it to the wall.

Lengkah 13: Potong Panels pikeun Nyocogkeun Kursus Top

On the final course, you’ll need to cut down the height of the panels to fit, removing the nailing strip so that the stone reaches to the top of the wall. Rest a flat panel in place and scribe a cutline on the back at the height of the wall. Set the panel on a work surface, and use the circular saw to cut it to the proper height. You may want to cut your corner pieces to length first, then cut them to the proper height, as shown. Dry-fit the two pieces at the corner to check the fit.

Lengkah 14: Lem Potongan

Leupaskeun panels sudut jeung nerapkeun manik lempeng tina napel konstruksi dina tonggong unggal sapotong dina ngalir nangtung, sakumaha ditémbongkeun, supados cai bébas ngalir balik panels na solokan leres. Atur panel dina tempatna dina témbok jeung saluyukeun aranjeunna pikeun pas snugly di juru.

Lengkah 15: Tilelep nu Fasteners

Pikeun langkung ngamankeun panel anu dipotong, panggihan sababaraha titik dina masing-masing tempat anjeun tiasa ngalelepkeun pengikat sacara teu jelas dina sambungan antara batu. Nyekel sapotong dina tempatna, bor liang pilot ngaliwatan panel jeung kana témbok. Ngajalankeun dina screw masonry, sinking sirah handap beungeut panel. Panutup screwheads kalawan caulk, ngumpulkeun sababaraha lebu tina méja motong, sarta niup kana caulk drying pikeun kamuflase eta. Anjeun tiasa nyabak naon waé jurang dina cara anu sami. Réngsé masang panel dina kursus ahir.

Lengkah 16: Potong Capstones

Pilih capstone sababaraha inci lega ti jero témbok clad Anjeun pikeun nyieun hiji overhang. Ukur sareng tandai capstones pikeun pas sapanjang luhureun témbok. Paké ragaji sirkular jeung sabeulah inten segmented motong kana panjangna, sakumaha ditémbongkeun.

Lengkah 17: Setel Batu ka Cap Tembok

Gawe sareng pasangan, angkat capstones tur garing-pas aranjeunna dina luhureun témbok. Cabut aranjeunna sareng nerapkeun napel konstruksi ka luhur témbok sareng ujung veneer sateuacan ngareset batu; atawa, lamun resep katingal malah leuwih otentik, Nyetél aranjeunna dina ranjang mortir kaku. Ayeuna mundur saléngkah sareng kagum kana tampilan anu mulus.