Bygg en tørrstablet støttemur-gal belegg

Vil du bygge din egen steinstøttemur, men usikker på hvordan du skal begynne? Hvis du har en ujevn hage, kan en steinstøttemur bidra til å forhindre erosjon og gir et fint sted å plante. For å lære hvordan du setter sammen dine egne, fra start til slutt, les videre.

 

To figure out how much stone you’ll need, multiply your wall’s height times the depth times the length. If your wall is 2 feet high, 1-1/2 feet wide, and 20 feet long, you’ll need roughly 60 cubic feet of stone. Most stoneyards will deliver the stones for a slight charge; have them placed as close to the site of your retaining wall as possible.

Når det gjelder tools, you’ll need a shovel for digging your trench and backfilling, a mattock for attacking the grade, and a small sledgehammer for tamping soil. For marking your site and leveling rocks, you’ll need a line level, a few tall stakes, string, some flour, and a 4- or 8-foot level.

 

So you’re all set with your verktøy, litt drikkevann, og kanskje noen låter å jobbe etter. Det første du må gjøre er å bestemme forsiden av veggen. Hvis den er rett, kan et brett eller en snor strukket mellom staker brukes til å markere linjen. Bruk ellers hageslange og merk kanten med mel.

 

Now you can start digging. The easiest approach is to cut and fill—that is, dig into the slope where the wall will go and spread the earth below you to create a level terrace. When you cut and fill, the wall is backed by undisturbed soil, which is more stable than fill. For design reasons, however, you might choose to build a freestanding wall and fill behind it with soil from another site. Or you might do a partial cut and fill, which is somewhere between the two.

Vegger bygges i kurs. The base course is structurally the most important, while the final course, the capstone, is the most challenging. For stability, walls should be at least 20 inches wide at the base. They can taper slightly toward the top, but you’ll want a wall that is at least two rocks wide in most places. This can be accomplished by mixing stones of different sizes or by backfilling with a combination of two-thirds rubble to one-third soil.

 

 Grav en grøft for bærelaget

Start by digging a trench about 4 inches deep and at least 2 feet wide. A straightedged spade will give you a nice, even edge. The first course must be very solid and tightly fit because the weight of the wall will rest on it. Take the time to find rocks that lock into place, without leaving gaps. Randomly lay your largest rocks along the front edge of the trench. Set the first stone, shifting it around until it sits securely without being rocked easily, and then fill with the remaining stones. If you are using rectangular stones, you want the height of adjacent stones to be the same, or of a difference that can be made up with a smaller stone. If the rocks are irregular, then the stones will fit together leaving a triangular gap for the next course to fit into. I find irregular rocks easier to work with than flat ones; with flat rocks you have to be more precise. Find a stone that fits well and then continue for a few more feet. A rule of thumb, passed down from my wall-building teacher’s mentor, is to try a stone seven different ways. If it doesn’t fit by the seventh try, use another stone.

Deretter må du måke skitt bak steinene og tampe jorden inn i mellomrommene between, behind, and beneath the stones with top of the sledgehammer. This is an important step because the dirt becomes the mortar for the wall. I also recommend adding rubble (those stones you won’t use on the face of your wall) behind the face course to give greater strength to the wall. Pound the rubble and soil mix until you are satisfied that it is solid. Continue the first course until you reach the end of the wall. When you are done, test

 kursen din ved å gå forsiktig på den. Steinene skal ikke rulle ut under vekten din.

 

For å begynne det andre kurset, velg en stein som vil bygge bro over den første leddet til det nederste kurset. Avoid having joints run up the face of the wall, and angle (batter) the courses backward—approximately 1 inch per vertical foot. This creates a stable wall. For added strength, intermittently place single stones that run the full depth of the wall. This will only work with rectangular rocks. For irregular rocks, place a large rock behind a face rock every 3 feet or so. As you set a course, you will come to situations, probably quite a few of them, where the rock placement is perfect on all sides but one. These are the planting opportunities that give life to a stone wall.

Continue building in this manner until you are one course away from the finished height. Fitting stones will get easier as you go, and you’ll likely discover that there’s a certain magic moment when you’re building a wall: you hear a thump that signals you’ve placed a rock perfec

 

Lag veggplasseringshøyden

The ideal height for a dry-stacked retaining wall is 18 to 22 inches—so you can sit on it when your gardening chores are done. Even if

you don’t plan to sit on your wall, 3 feet is about as high as I would recommend building any dry-stacked wall; higher walls should be engineered for stability. Using your stakes, string, and line level, mark the height of the capstone. You’ll also want to check the level of individual stones as you go. It’s difficult to get the capstone perfectly level, but a 1-inch variance looks level overall.

 

Ta med mye tålmodighet til prosessen med å legge dekksteinen; det er en kulminasjon av ferdigheten du har utviklet til dette punktet. Den skal være omtrent 15 til 18 tommer dyp, bestående av en til tre steiner. Bruk jord og god plassering for å sikre steinene, og unngå på samme måte som med veggfuger lange fuger i dekksteinen. Hvis du vil sitte på veggen, velg glatte, flate steiner. Eller fyll hull med jord og plant duftende urter til puter. En plantet toppstein er en herlig prikken over i'en på en levende vegg.